Filter oil mist collector OMC-F series
99.8 % or higher collection rate! Low cost, high performance and energy saving
Features
| Type | Specifications | ||
| Filter | Energy saving | High collection rate | Provided with Air volume indicator |
Certificates/Approvals
| EU RoHS2 | China RoHS | CE | UL | CSA | PSE |
Quick Selection
Model/Specifications
| Model | OMC-F105A | OMC-F110A | OMC-F120A | |
| Max. air flow | 4.2/5m3/min | 8/10m3/min | 18/20m3/min | |
| Collection efficiency | Min. 99.8% (by gravimetric method) | |||
| Rated voltage | 3-phase, 200VAC 50/60Hz | |||
| Rated motor output | 0.3kW（2P） | 0.4kW（2P） | 1.12kW（2P） | |
| Rated current consumption ※1 | 1.6/1.6A or less | 2.0/2.0A or less | 4.7/4.5A or less | |
| Working temperature | 0 to ＋40℃ | |||
| Working humidity | Max. 85%RH, free from condensation | |||
| Noise (at 1m) | 57dB(A) | 63dB(A) | 66dB(A) | |
| Max. suction air temperature | ＋50℃ | |||
| Environmental standard | RoHS2 | |||
| Suction port diameter | Ø100mm | Ø125mm | Ø150mm | |
| Weight | 25.0kg | 30.0kg | 50.0kg | |
| Drain port | Ø19 pipe | |||
Mechanism
- Larger particles in the incoming air are filtered by inertial collision as a primary step.
- Smaller particles escaped from the primary filter are trapped by the secondary filter and then by the tertiary filter.
- Clean air goes out through the exhaust port.
Product lineup
OMC-F105A
Max. air flow
4.2/5m3/min
A complete set of supply
Oil Mist Collector : 1 unit Ø 100 Duct flange : 1 pc. Duct hose band : 2 pcs.
Drain hose : 2m long Drain hose band : 1 pc. Anti-vibration rubber : 4 pcs. Instruction manual : 1 copy
Drain hose : 2m long Drain hose band : 1 pc. Anti-vibration rubber : 4 pcs. Instruction manual : 1 copy
Collection efficiency
Test oil : Water-insoluble cutting oil
Measuring instrument : Low volume air sampler type AN-200
Measuring instrument : Low volume air sampler type AN-200
Dimensional drawing
Mounting hole processing
Mounting cutout for duct flange
Max. air flow
8/10m3/min
A complete set of supply
Oil Mist Collector : 1 unit Ø 125 Duct flange : 1 pc. Duct hose band : 2 pcs.
Drain hose : 2m long Drain hose band : 1 pc. Anti-vibration rubber : 4 pcs. Instruction manual : 1 copy
Drain hose : 2m long Drain hose band : 1 pc. Anti-vibration rubber : 4 pcs. Instruction manual : 1 copy
Collection efficiency
Test oil : Water-insoluble cutting oil
Measuring instrument : Low volume air sampler type AN-200
Measuring instrument : Low volume air sampler type AN-200
Dimensional drawing
Mounting hole processing
Mounting cutout for duct flange
Max. air flow
18/20m3/min
A complete set of supply
Oil Mist Collector : 1 unit Drain hose : 2m long Drain hose band : 1 pc. Instruction manual : 1 copy
Collection efficiency
Test oil : Water-insoluble cutting oil
Measuring instrument : Low volume air sampler type AN-200
Measuring instrument : Low volume air sampler type AN-200
Dimensional drawing
Mounting hole processing
Mounting cutout for duct flange
Optional parts for OMC-F
Filter, Duct hose, etc.
Cautions
・This product is intended for collecting general watersoluble and oil mist that generates during production process using various machine tools. Never have it inhale the following substances.
- Flammable substances such as gasoline, thinner, benzin, kerosene and others as well as oil and cleaning liquid with an ignition point 70 degrees C or below,
- Explosive substances such as aluminium, magnesium and titan as well as materials ridden with those substances,
- Flammable liquid, mist and materials ridden with these substances,
- Corrosive and adhesive substances and hazardous gas or air with a lot of unusual substances
- Dust
- Hot air exceeding 50 deg. C.
- Large amount of liquid,
- Substances that remarkably accelerate rusting of metals or aging of plastics
・This product should not be used in an atmosphere which contains chlorine, sulfuric or fluorine gasses, oxalic acid, xylene, or methyl tetrachloride and the like.
・Do not use this product in a corrosive atmosphere.
・Tampering or repairing the product should be strictly avoided. Please contact us for repairing service.
・Do not operate the product with its terminal box uncovered.
・Never touch the motor while the unit is in operation. Do not put your fingers or foreign matters into the rotating part of fan.
・Indoor use only. The altitude of the site of use should be lower than 2000 m.
・The site of use should be free from vibration or impact.
・Make sure that the packaging is not damaged on delivery.
・Use this product within the temperature range from 0℃ to +40℃ and humidity not exceeding 85%RH (no condensation).
・Impact, vibration or excess load should be avoided during transportation.
・Precision apparatuses should not be arranged near the exhaust port where fine particles may fall on.
- Flammable substances such as gasoline, thinner, benzin, kerosene and others as well as oil and cleaning liquid with an ignition point 70 degrees C or below,
- Explosive substances such as aluminium, magnesium and titan as well as materials ridden with those substances,
- Flammable liquid, mist and materials ridden with these substances,
- Corrosive and adhesive substances and hazardous gas or air with a lot of unusual substances
- Dust
- Hot air exceeding 50 deg. C.
- Large amount of liquid,
- Substances that remarkably accelerate rusting of metals or aging of plastics
・This product should not be used in an atmosphere which contains chlorine, sulfuric or fluorine gasses, oxalic acid, xylene, or methyl tetrachloride and the like.
・Do not use this product in a corrosive atmosphere.
・Tampering or repairing the product should be strictly avoided. Please contact us for repairing service.
・Do not operate the product with its terminal box uncovered.
・Never touch the motor while the unit is in operation. Do not put your fingers or foreign matters into the rotating part of fan.
・Indoor use only. The altitude of the site of use should be lower than 2000 m.
・The site of use should be free from vibration or impact.
・Make sure that the packaging is not damaged on delivery.
・Use this product within the temperature range from 0℃ to +40℃ and humidity not exceeding 85%RH (no condensation).
・Impact, vibration or excess load should be avoided during transportation.
・Precision apparatuses should not be arranged near the exhaust port where fine particles may fall on.
